View MB90860A_669307.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

FUJITSU SEMICONDUCTOR DATA SHEET
DS07-13732-2E
16-bit Proprietary Microcontroller
CMOS
F2MC-16LX MB90860A Series
MB90F867A (S) , MB90867A (S)
s DESCRIPTION
The MB90860A-series is Fujitsu 16-bit general-purpose microcontroller which enhances each kind of timers and communication macros. With the new 0.35 m CMOS technology, Fujitsu now offers 128 Kbytes on-chip FLASHROM program memory. An internal voltage booster removes the necessity for a second programming voltage. The power supply (3 V) is supplied to the internal MCU core from an internal regulator circuit. This creates a major advantage in terms of EMI and power consumption. The internal PLL clock frequency multiplier provides an internal 42 ns instruction cycle time from an external 4 MHz clock. The unit features an 8 channel Output Compare Unit and 8 channel Input Capture Unit with 2 separate 16-bit free running timers. 4 UARTs constitute additional functionality for communication purposes. Note : F2MC stands for FUJITSU Flexible Microcontroller, a registered trademark of FUJITSU LIMITED.
s PACKAGES
100-pin Plastic QFP 100-pin Plastic LQFP
(FPT-100P-M06)
(FPT-100P-M05)
MB90860A Series
s FEATURES
* Clock * Built-in PLL clock frequency multiplication circuit * Selection of machine clocks (PLL clocks) is allowed among frequency division by two on oscillation clock, and multiplication of 1 to 6 times of oscillation clock (for 4 MHz oscillation clock, 4 MHz to 24 MHz). * Operation by sub-clock (up to 50 kHz : 100 kHz oscillation clock divided by two) is allowed. (devices without S-suffix only) * Minimum execution time of instruction : 42 ns (when operating with 4-MHz oscillation clock, and 6-time multiplied PLL clock). * 16 Mbyte CPU memory space * 24-bit internal addressing * Instruction system best suited to controller * Wide choice of data types (bit, byte, word, and long word) * Wide choice of addressing modes (23 types) * Enhanced multiply-divide instructions and RETI instructions * Enhanced high-precision computing with 32-bit accumulator * Instruction system compatible with high-level language (C language) and multitask * Employing system stack pointer * Enhanced various pointer indirect instructions * Barrel shift instructions * Increased processing speed * 4-byte instruction queue * Powerful interrupt function * Powerful 8-level, 34-condition interrupt feature * Up to 16 external interrupts are supported * Automatic data transfer function independent of CPU * Extended intelligent I/O service function (EI2OS) : up to 16 channels * DMA : up to 16 channels * Low power consumption (standby) mode * Sleep mode (a mode that halts CPU operating clock) * Time-base timer mode (a mode that operates oscillation clock, sub clock, time-base timer and clock timer only) * Watch mode (a mode that operates sub clock and clock timer only) * Stop mode (a mode that stops oscillation clock and sub clock) * CPU blocking operation mode * Process * CMOS technology * I/O port * General-purpose input/output port (CMOS output) - 80 ports (devices without S-suffix) - 82 ports (devices with S-suffix)
(Continued)
2
MB90860A Series
(Continued)
* Timer * Time-base timer, clock timer, watchdog timer : 1 channel * 8/16-bit PPG timer : 8-bit X 16 channels, or 16-bit X 8 channels * 16-bit reload timer : 4 channels * 16- bit input/output timer - 16-bit free run timer : 2 channel (FRT0 : ICU 0/1/2/3, OCU 0/1/2/3, FRT1 : ICU 4/5/6/7, OCU 4/5/6/7) - 16- bit input capture: (ICU) : 8 channels - 16-bit output compare : (OCU) : 8 channels * UART (LIN/SCI) : 4 channels * Equipped with full-duplex double buffer * Clock-asynchronous or clock-synchronous serial transmission is available * I2C interface* : 2 channels * Up to 400 kbit/s transfer rate * DTP/External interrupt : 16 channels, CAN wakeup : 2 channels * Module for activation of extended intelligent I/O service (EI2OS), DMA, and generation of external interrupt. * Delay interrupt generator module * Generates interrupt request for task switching. * 8/10-bit A/D converter : 24 channels * Resolution is selectable between 8-bit and 10-bit. * Activation by external trigger input is allowed. * Conversion time : 3 s (at 24-MHz machine clock, including sampling time) * Program patch function * Address matching detection for 6 address pointers. * Internal voltage regulator * Supports 3 V MCU core, offering low EMI and low power consumption figures * Programmable input levels * Automotive/CMOS-Schmitt (initial level is Automotive in Single chip mode) * TTL level (initial level for External bus mode) * ROM security function * Protects the content of ROM (MASK ROM device only) * Flash security function * Protects the content of Flash (Flash device only) * External bus interface * Clock monitor function * : I2C license : Purchase of Fujitsu I2C components conveys a license under the Philips I2C Patent Rights to use, these components in an I2C system provided that the system conforms to the I2C standard Specification as defined by Philips.
3
MB90860A Series
s PRODUCT LINEUP
Part Number MB90F867A (S) , MB90867A (S) Parameter CPU System clock ROM RAM Emulator-specific power supply*1 Technology Operating voltage range Temperature range Package F2MC-16LX CPU On-chip PLL clock multiplier (x1, x2, x3, x4, x6, 1/2 when PLL stops) Minimum instruction execution time : 42 ns (4 MHz osc. PLL x 6)
Boot-block,Flash memory 128 Kbytes 6 Kbytes
MB90V340(S)
External 30 Kbytes Yes 0.35 m CMOS with on-chip voltage regulator for internal power supply 5 V 10% PGA-299 5 channels
0.35 m CMOS with on-chip voltage regulator for internal power supply + Flash memory with On-chip charge pump for programming voltage 3.5 V to 5.5 V : at normal operating (not using A/D converter) 4.0 V to 5.5 V : at using A/D converter/Flash programming 4.5 V to 5.5 V : at using external bus -40 C to +105 C QFP-100, LQFP-100 4 channels
UART
Wide range of baud rate settings using a dedicated reload timer Special synchronous options for adapting to different synchronous serial protocols LIN functionality working either as master or slave LIN device 2 channel 24 input channels 10-bit or 8-bit resolution Conversion time : Min 3 s include sample time (per one channel) Operation clock frequency : fsys/21, fsys/23, fsys/25 (fsys = Machine clock frequency) Supports External Event Count function Signals an interrupt when overflowing Supports Timer Clear when a match with Output Compare (Channel 0, 4) Operation clock freq. : fsys, fsys/21, fsys/22, fsys/23, fsys/24, fsys/25, fsys/26, fsys/27 (fsys = Machine clock freq.) I/O Timer 0 (clock input FRCK0) corresponds to ICU 0/1/2/3, OCU 0/1/2/3 I/O Timer 1 (clock input FRCK1) corresponds to ICU 4/5/6/7, OCU 4/5/6/7
I2C (400 Kbit/s) A/D Converter 16-bit Reload Timer (4 channels) 16-bit I/O Timer (2 channels)
16-bit Output Compare Signals an interrupt when 16-bit I/O Timer match output compare registers. (8 channels (16-bit) / A pair of compare registers can be used to generate an output signal. 16 channels (8-bit) ) 16-bit Input Capture (8 channels) Rising edge, falling edge or rising & falling edge sensitive Signals an interrupt upon external event
(Continued)
4
MB90860A Series
(Continued) Part Number
MB90F867A (S) , MB90867A (S) Parameter Supports 8-bit and 16-bit operation modes Sixteen 8-bit reload counters 8/16-bit Sixteen 8-bit reload registers for L pulse width Programmable Pulse Sixteen 8-bit reload registers for H pulse width Generator A pair of 8-bit reload counters can be configured as one 16-bit reload counter or as (8 channels) 8-bit prescaler plus 8-bit reload counter Operation clock freq. : fsys, fsys/21, fsys/22, fsys/23, fsys/24 or 128 s@fosc = 4 MHz (fsys = Machine clock frequency, fosc = Oscillation clock frequency) CAN Interface External Interrupt (16 channels) D/A converter Up to100 kHz Subclock for low power operation 3 channels Can be used rising edge, falling edge, starting up by H/L level input, external interrupt, expanded inteligent I/O services (EI2OS) and DMA devices with `S'-suffix : without subclock devices without `S'-suffix : with subclock Virtually all external pins can be used as general purpose I/O port All push-pull outputs Bit-wise settable as input/output or peripheral signal Settable in pin-wise of 8 as CMOS schmitt trigger/ automotive inputs (default) TTL input level settable for external bus (32-pin only for external bus) Supports automatic programming, Embedded AlgorithmTM*2 Write/Erase/Erase-Suspend/Resume commands A flag indicating completion of the algorithm Number of erase cycles : 10,000 times Data retention time : 20 years Boot block configuration Erase can be performed on each block Block protection with external programming voltage Flash Security Feature for protecting the content of the Flash 2 channels MB90V340(S)
I/O Ports
Flash Memory
*1 : It is setting of Jumper switch (TOOL VCC) when Emulator (MB2147-01) is used. Please refer to the Emulator hardware manual about details. *2 : Embedded Algorithm is a trade mark of Advanced Micro Devices Inc.
5
MB90860A Series
s PIN ASSIGNMENTS
* MB90F867A (S) , MB90867A (S) (TOP VIEW)
P03/AD03/INT11 P02/AD02/INT10 P01/AD01/INT9 P00/AD00/INT8 PA 1 PA0/INT8R P97/OUT3 P96/OUT2 P95/OUT1 P94/OUT0 P93/PPG7(6) P92/PPG5(4) P91/PPG3(2) P90/PPG1(0) Vss Vcc P87/SCK1 P86/SOT1 P85/SIN1 P84/SCK0/INT15R P83/SOT0/TOT2 P82/SIN0/TIN2/INT14R P81/TOT0/CKOT/INT13R P80/TIN0/ADTG/INT12R P77/AN23/INT7 P76/AN22/INT6
MD0 MD1
P04/AD04/INT12 P05/AD05/INT13 P06/AD06/INT14 P07/AD07/INT15 P10/AD08/TIN1 P11/AD09/TOT1 P12/AD10/SIN3/NT11R P13/AD11/SOT3 P14/AD12/SCK3 Vcc Vss X1 X0 P15/AD13 P16/AD14 P17/AD15 P20/A16/PPG9(8) P21/A17/PPGB(A) P22/A18/PPGD(C) P23/A19/PPGF(E)
80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 81 82 49 83 48 84 47 85 46 86 45 87 44 88 43 89 42 QFP - 100 90 41 91 40 92 39 93 38 94 37 95 36 96 35 97 34 98 33 99 32 100 31 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 P31/RD/IN5 P32/WRL/WR/INT10R P35/HAK/OUT5 P36/RDY/OUT6 P37/CLK/OUT7 P40/X0A* P41/X1A* Vcc Vss C P42/IN6/INT9R P43/IN7 P44/SDA0/FRCK0 P45/SCL0/FRCK1 P46/SDA1 P47/SCL1 P50/AN8/SIN2 P51/AN9/SOT2 P52/AN10/SCK2 P53/AN11/TIN3 P54/AN12/TOT3 P55/AN13 P56/AN14 P33/WRH P34/HRQ/OUT4 P24/A20/IN0 P25/A21/IN1 P26/A22/IN2 P27/A23/IN3 P30/ALE/IN4
MD2
RST
P75/AN21/INT5 P74/AN20/INT4 P73/AN19/INT3 P72/AN18/INT2 P71/AN17/INT1 P70/AN16/INT0 Vss P67/AN7/PPGE(F) P66/AN6/PPGC(D) P65/AN5/PPGA(B) P64/AN4/PPG8(9) P63/AN3/PPG6(7) P62/AN2/PPG4(5) P61/AN1/PPG2(3) P60/AN0/PPG0(1) AVss AVRL AVRH AVcc P57/AN15
(FPT-100P-M06)
* : MB90F867A, MB90867A : X0A, X1A MB90F867AS, MB90867AS : P40, P41
(Continued)
6
MB90860A Series
(Continued)
(TOP VIEW)
P81/TOT0/CKOT/INT13R P80/TIN0/ADTG/INT12R P77/AN23/INT7 P76/AN22/INT6 P00/AD00/INT8 PA 1 PA0/INT8R P97/OUT3 P96/OUT2 P95/OUT1 P94/OUT0 P93/PPG7(6) P92/PPG5(4) P91/PPG3(2) P90/PPG1(0) Vss Vcc P87/SCK1 P86/SOT1 P85/SIN1 P84/SCK0/INT15R P83/SOT0/TOT2 P82/SIN0/TIN2/INT14R
P01/AD01/INT9 P02/AD02/INT10 P03/AD03/INT11 P04/AD04/INT12 P05/AD05/INT13 P06/AD06/INT14 P07/AD07/INT15 P10/AD08/TIN1 P11/AD09/TOT1 P12/AD10/SIN3/NT11R P13/AD11/SOT3 P14/AD12/SCK3 Vcc Vss X1 X0 P15/AD13 P16/AD14 P17/AD15 P20/A16/PPG9(8) P21/A17/PPGB(A) P22/A18/PPGD(C) P23/A19/PPGF(E) P24/A20/IN0 P25/A21/IN1
75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 76 50 77 49 78 48 47 79 46 80 45 81 44 82 43 83 42 84 41 85 40 86 39 87 LQFP - 100 38 88 37 89 36 90 35 91 34 92 33 93 32 94 31 95 30 96 29 97 98 28 99 27 100 26 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 P31/RD/IN5 P32/WRL/WR/INT10R P35/HAK/OUT5 P36/RDY/OUT6 P37/CLK/OUT7 P40/X0A* P41/X1A* Vcc Vss C P42/IN6//INT9R P43/IN7 P44/SDA0/FRCK0 P45/SCL0/FRCK1 P46/SDA1 P47/SCL1 P50/AN8/SIN2 P51/AN9/SOT2 P52/AN10/SCK2 P53/AN11/TIN3 P33/WRH P34/HRQ/OUT4 P26/A22/IN2 P27/A23/IN3 P30/ALE/IN4
MD0
RST
MD1 MD2 P75/AN21/INT5 P74/AN20/INT4 P73/AN19/INT3 P72/AN18/INT2 P71/AN17/INT1 P70/AN16/INT0 Vss P67/AN7/PPGE(F) P66/AN6/PPGC(D) P65/AN5/PPGA(B) P64/AN4/PPG8(9) P63/AN3/PPG6(7) P62/AN2/PPG4(5) P61/AN1/PPG2(3) P60/AN0/PPG0(1) AVss AVRL AVRH AVcc P57/AN15 P56/AN14 P55/AN13 P54/AN12/TOT3
(FPT-100P-M05)
* : MB90F867A, MB90867A : X0A, X1A MB90F867AS, MB90867AS : P40, P41
7
MB90860A Series
s PIN DESCRIPTION
Pin No. LQFP100*2 QFP100*1 90 91 52 92 93 54 Pin name X1 X0 RST P00 to P07 75 to 82 77 to 84 AD00 to AD07 INT8 to INT15 P10 83 85 AD08 TIN1 P11 84 86 AD09 TOT1 P12 85 87 N G G G Circuit type A E Oscillation output Oscillation input Reset input General purpose I/O. The register can be set to select whether to use a pull-up resistor. This function is enabled in single-chip mode. I/O pins for 8 lower bits of the external address/data bus. This function is enabled when the external bus is enabled. External interrupt request input pins for INT8 to INT15. General purpose I/O. The register can be set to select whether to use a pull-up resistor. This function is enabled in single-chip mode. I/O pin for bit 8 of the external address/data bus. This function is enabled when the external bus is enabled. Event input pin for the reload timer 1 General purpose I/O. The register can be set to select whether to use a pull-up resistor. This function is enabled in single-chip mode. I/O pin for bit 9 of the external address/data bus. This function is enabled when the external bus is enabled. Output pin for the reload timer 1 General purpose I/O. The register can be set to select whether to use a pull-up resistor. This function is enabled in single-chip mode. I/O pin for bit 10 of the external address/data bus. This function is enabled when the external bus is enabled. Serial data input pin for UART3 Sub external interrupt request input pin for INT11 General purpose I/O. The register can be set to select whether to use a pull-up resistor. This function is enabled in single-chip mode. G AD11 SOT3 P14 87 89 AD12 SCK3 G I/O pin for bit 11 of the external address/data bus. This function is enabled when the external bus is enabled. Serial data output pin for UART3 General purpose I/O. The register can be set to select whether to use a pull-up resistor. This function is enabled in single-chip mode. I/O pin for bit 12 of the external address/data bus. This function is enabled when the external bus is enabled. Clock I/O pin for UART3 Function
AD10 SIN3 INT11R P13
86
88
(Continued)
8
MB90860A Series
Pin No. LQFP100*
2
QFP100*
1
Pin name
Circuit type
Function General purpose I/O. The register can be set to select whether to use a pull-up resistor. This function is enabled in single-chip mode.
P15 92 94 AD13 SIN4 P16 93 95 AD14 SOT4 P17 94 96 AD15 SCK4 G G G
I/O pin for bit 13 of the external address/data bus. This function is enabled when the external bus is enabled. Serial data input pin for UART4 (MB90V340 only) General purpose I/O. The register can be set to select whether to use a pull-up resistor. This function is enabled in single-chip mode. I/O pin for bit 14 of the external address/data bus. This function is enabled when the external bus is enabled. Serial data output pin for UART4 (MB90V340 only) General purpose I/O. The register can be set to select whether to use a pull-up resistor. This function is enabled in single-chip mode. I/O pin for bit 15 of the external address/data bus. This function is enabled when the external bus is enabled. Clock I/O pin for UART4 (MB90V340 only) General purpose I/O. The register can be set to select whether to use a pull-up resistor.In external bus mode, the pin is enabled as a general-purpose I/O port when the corresponding bit in the external address output control register (HACR) is 1.
P20 to P23
95 to 98
97 to 100 A16 to A19
G
Output pins for A16 to A19 of the external address bus. When the corresponding bit in the external address output control register (HACR) is 0, the pins are enabled as high address output pins (A16 to A19). Output pins for PPGs General purpose I/O. The register can be set to select whether to use a pull-up resistor.In external bus mode, the pin is enabled as a general-purpose I/O port when the corresponding bit in the external address output control register (HACR) is 1.
PPG9,PPGB, PPGD,PPGF
P24 to P27
99 to 2
1 to 4 A20 to A23
G
Output pins for A20 to A23 of the external address bus. When the corresponding bit in the external address output control register (HACR) is 0, the pins are enabled as high address output pins (A20 to A23). Data sample input pins for input captures ICU0 to ICU3 General purpose I/O.The register can be set to select whether to use a pull-up resistor.This function is enabled in single-chip mode.
IN0 to IN3 P30 3 5 ALE IN4 G
Address latch enable output pin. This function is enabled when the external bus is enabled. Data sample input pin for input capture ICU4
(Continued)
9
MB90860A Series
Pin No. LQFP100* QFP100*
2 1
Pin name
Circuit type
Function General purpose I/O.The register can be set to select whether to use a pull-up resistor.This function is enabled in single-chip mode.
P31 4 6 RD IN5 P32 G
Read strobe output pin for the data bus. This function is enabled when the external bus is enabled. Data sample input pin for input capture ICU5 General purpose I/O. The register can be set to select whether to use a pull-up resistor. This function is enabled either in single-chip mode or with the WR/WRL pin output disabled. Write strobe output pin for the data bus. This function is enabled when both the external bus and the WR/WRL pin output are enabled. WRL is used to write-strobe 8 lower bits of the data bus in 16-bit access while WR is used to write-strobe 8 bits of the data bus in 8-bit access. RX input pin for CAN2 Interface (MB90V340 only) Sub external interrupt request input pin for INT10 General purpose I/O. The register can be set to select whether to use a pull-up resistor.This function is enabled either in single-chip mode or with the WRH pin output disabled.
5
7
WRL / WR
G
RX2 INT10R P33
6
8 WRH
G
Write strobe output pin for the 8 higher bits of the data bus. This function is enabled when the external bus is enabled, when the external bus 16-bit mode is selected, and when the WRH output pin is enabled. TX Output pin for CAN2 (MB90V340 only) General purpose I/O. The register can be set to select whether to use a pull-up resistor. This function is enabled either in single-chip mode or with the hold function disabled.
TX2 P34 7 9 HRQ OUT4 P35 8 10 HAK OUT5 P36 9 11 RDY OUT6 G G G
Hold request input pin. This function is enabled when both the external bus and the hold function are enabled. Waveform output pin for output compare OCU4 General purpose I/O. The register can be set to select whether to use a pull-up resistor. This function is enabled either in single-chip mode or with the hold function disabled. Hold acknowledge output pin. This function is enabled when both the external bus and the hold function are enabled. Waveform output pin for output compare OCU5 General purpose I/O. The register can be set to select whether to use a pull-up resistor. This function is enabled either in single-chip mode or with the external ready function disabled. Ready input pin. This function is enabled when both the external bus and the external ready function are enabled. Waveform output pin for output compare OCU6
(Continued)
10
MB90860A Series
Pin No. LQFP100*
2
QFP100*
1
Pin name
Circuit type
Function General purpose I/O. The register can be set to select whether to use a pull-up resistor. This function is enabled either in single-chip mode or with the CLK output disabled.
P37 10 12 CLK OUT7 11 to 12 13 to 14 P40 , P41 X0A , X1A P42 16 18 IN6 RX1 INT9R P43 17 19 IN7 TX1 P44 18 20 SDA0 FRCK0 P45 19 21 SCL0 FRCK1 20 21 22 23 P46 SDA1 P47 SCL1 P50 22 24 AN8 SIN2 P51 23 25 AN9 SOT2 P52 24 26 AN10 SCK2 P53 25 27 AN11 TIN3 I I I O H H H H F F F B G
CLK output pin. This function is enabled when both the external bus and CLK output are enabled. Waveform output pin for output compare OCU7 General purpose I/O (devices with S-suffix) Oscillator input pins for sub-clock (devices without S-suffix) General purpose I/O Data sample input pin for input capture ICU6 RX input pin for CAN1 (MB90V340 (S) only) Sub external interrupt request input pin for INT10 General purpose I/O Data sample input pin for input capture ICU7 TX Output pin for CAN1 (MB90V340 (S) only) General purpose I/O Serial data I/O pin for I2C 0 Input for the 16-bit I/O Timer 0 General purpose I/O Serial clock I/O pin for I2C 0 Input for the 16-bit I/O Timer 1 General purpose I/O Serial data I/O pin for I2C 1 General purpose I/O Serial clock I/O pin for I2C 1 General purpose I/O Analog input pin for the A/D converter Serial data input pin for UART2 General purpose I/O Analog input pin for the A/D converter Serial data output pin for UART2 General purpose I/O Analog input pin for the A/D converter Clock I/O pin for UART2 General purpose I/O Analog input pin for the A/D converter Event input pin for the reload timer 3
(Continued)
11
MB90860A Series
Pin No. LQFP100* 26
2
QFP100* 28
1
Pin name P54 AN12 TOT3 P55 AN13 P56 to P57 AN14 to AN15 DA00 to DA01 P60 to P67 AN0 to AN7 PPG0, 2, 4, 6, 8, A, C, E P70 to P77
Circuit type General purpose I/O I
Function
Analog input pin for the A/D converter Output pin for the reload timer 3 General purpose I/O Analog input pin for the A/D converter General purpose I/O Analog input pin for the A/D converter D/A converter analog output pins (MB90V340 only) General purpose I/O Analog input pins for the A/D converter Output pins for PPGs General purpose I/O
27
29
I
28, 29
30, 31
J
34 to 41
36 to 43
I
43 to 48, 53, 54
45 to 50, 55, 56
AN16 to AN23 INT0 to INT7 P80 TIN0 ADTG INT12R P81 TOT0 CKOT INT13R P82 SIN0 TIN2 INT14R P83
I
Analog input pins for the A/D converter (devices with C-suffix) External interrupt request input pins for INT0 to INT7 General purpose I/O Event input pin for the reload timers 0 Trigger input pin for the A/D converter Sub external interrupt request input pin for INT12 General purpose I/O Output pin for the reload timer 0 Output pin for the clock monitor Sub external interrupt request input pin for INT13 General purpose I/O Serial data input pin for UART0 Event input pin for the reload timers 2 Sub external interrupt request input pin for INT14 General purpose I/O
55
57
F
56
58
F
57
59
M
58
60
SOT0 TOT2 P84
F
Serial data output pin for UART0 Output pin for the reload timer 2 General purpose I/O
59
61
SCK0 INT15R P85 SIN1 P86 SOT1
F
Clock I/O pin for UART0 Sub external interrupt request input pin for INT15 General purpose I/O Serial data input pin for UART1 General purpose I/O Serial data output pin for UART1
60 61
62 63
M F
(Continued)
12
MB90860A Series
(Continued) Pin No.
LQFP100* 62 65 to 68
2
QFP100* 64 67 to 70
1
Pin name P87 SCK1 P90 to P93 PPG1, 3, 5, 7 P94 to P97
Circuit type F F General purpose I/O Clock I/O pin for UART1 General purpose I/O Output pins for PPGs General purpose I/O F
Function
69 to 72
71 to 74
OUT0 to OUT3 PA0
Waveform output pins for output compares OCU0 to OCU3. This function is enabled when the OCU enables waveform output. General purpose I/O RX input pin for CAN0 (MB90V340 (s) only) Sub external interrupt request input pin for INT8 General purpose I/O TX Output pin for CAN0 (MB90V340 (s) only) Vcc power input pin for analog circuits Reference voltage input for the A/D Converter. This power supply must be turned on or off while a voltage higher than or equal to AVRH is applied to AVCC. Lower reference voltage input for the A/D Converter Vss power input pin for analog circuits Input pins for specifying the operating mode. The pins must be directly connected to Vcc or Vss Input pin for specifying the operating mode. The pins must be directly connected to Vcc or Vss. Power (3.5 V to 5.5 V) input pins
73
75
RX0 INT8R PA1 TX0 AVCC AVRH AVRL AVSS MD1, MD0 MD2
F
74 30 31 32 33 50, 51 49 13 63 88 14 42 64 89 15
76 32 33 34 35 52, 53 51 15 65 90 16 44 66 91 17
F K L K K C D
VCC
VSS
Power (0V) input pins
C
K
This is the power supply stabilization capacitor pin. It should be connected to a higher than or equal to 0.1 F ceramic capacitor.
*1 : FPT-100P-M06 *2 : FPT-100P-M05
13
MB90860A Series
s I/O CIRCUIT TYPE
Type Circuit Remarks Oscillation circuit * High-speed oscillation feedback resistor = approx. 1 M
X1
Xout
A
X0
Standby control signal
X1A
Xout
Oscillation circuit * Low-speed oscillation feedback resistor = approx. 10 M
B
X0A
Standby control signal
Mask ROM and EVA device: * CMOS Hysteresis input pin C
R Hysteresis inputs
Flash device: * CMOS input pin Mask ROM and EVA device: * CMOS Hysteresis input pin * Pull-down resistor valule: approx. 50 k Flash device: * CMOS input pin * No Pull-down
R Hysteresis inputs
D
Pull-down Resistor
CMOS Hysteresis input pin * Pull-up resistor valule: approx. 50 k E
Pull-up Resistor R Hysteresis inputs
(Continued)
14
MB90860A Series
Type
Circuit
Remarks * CMOS level output(IOL = 4 mA, IOH = -4 mA) * CMOS hysteresis inputs (With the standby-time input shutdown function) * Automotive input (With the standby-time input shutdown function)
Pout
Nout
F
R Hysteresis inputs
Automotive inputs Standby control for input shutdown pull-up control
Pout
Nout
G
R Hysteresis inputs
* CMOS level output(IOL = 4 mA, IOH = -4 mA) * CMOS hysteresis inputs (With the standby-time input shutdown function) * Automotive input (With the standby-time input shutdown function) * TTL input (With the standby-time input shutdown function) * Programmalble pullup resistor: 50 k approx.
Automotive inputs
TTL input Standby control for input shutdown
Pout
Nout
* CMOS level output(IOL = 3 mA, IOH = -3 mA) * CMOS hysteresis inputs (With the standby-time input shutdown function) * Automotive input (With the standby-time input shutdown function)
H
R Hysteresis inputs
Automotive inputs Standby control for input shutdown
(Continued)
15
MB90860A Series
Type
Circuit
Remarks * CMOS level output(IOL = 4 mA, IOH = -4 mA) * CMOS hysteresis inputs (With the standbytime input shutdown function) * Automotive input (With the standby-time input shutdown function) * A/D analog input
Pout
Nout R
I
Hysteresis inputs
Automotive inputs Standby control for input shutdown Analog input
Pout
Nout R
* CMOS level output(IOL = 4 mA, IOH = -4 mA) * D/A analg output * CMOS hysteresis inputs (With the standbytime input shutdown function) * Automotive input (With the standby-time input shutdown function) * A/D analog input
J
Hysteresis inputs
Automotive inputs Standby control for input shutdown Analog input Analog output
* Power supply input protection circuit
K
ANE
L
AVR ANE
* A/D converter reference voltage power supply input pin, with the protection circuit * Flash devices do not have a protection circuit against VCC for pin AVRH
(Continued)
16
MB90860A Series
(Continued) Type
Circuit
Remarks * CMOS level output(IOL = 4 mA, IOH = -4 mA) * CMOS inputs (With the standby-time input shutdown function) * Automotive input (With the standby-time input shutdown function)
Pout
Nout
M
R CMOS inputs
Automotive inputs Standby control for input shutdown pull-up control
Pout
Nout
N
R CMOS inputs
* CMOS level output(IOL = 4 mA, IOH = -4 mA) * CMOS inputs (With the standby-time input shutdown function) * Automotive input (With the standby-time input shutdown function) * TTL input (With the standby-time input shutdown function) Programmable pullup registor:50 k approx.
Automotive inputs
TTL input Standby control for input shutdown
Pout
Nout R
* CMOS level output(IOL = 4 mA, IOH = -4 mA) * CMOS inputs (With the standby-time input shutdown function) * Automotive input (With the standby-time input shutdown function) * A/D analog input
O
CMOS inputs
Automotive inputs Standby control for input shutdown Analog input
17
MB90860A Series
s HANDLING DEVICES
Special care is required for the following when handling the device : * Preventing latch-up * Treatment of unused pins * Using external clock * Precautions for when not using a sub clock signal * Notes on during operation of PLL clock mode * Power supply pins (VCC/VSS) * Pull-up/down resistors * Crystal Oscillator Circuit * Turning-on Sequence of Power Supply to A/D Converter and Analog Inputs * Connection of Unused Pins of A/D Converter * Notes on Energization * Stabilization of power supply voltage * Initialization * Port0 to port3 output during Power-on(External-bus mode) * Flash security Function
1. Preventing latch-up
CMOS IC chips may suffer latch-up under the following conditions : * A voltage higher than VCC or lower than VSS is applied to an input or output pin. * A voltage higher than the rated voltage is applied between VCC and VSS. * The AVCC power supply is applied before the VCC voltage. Latch-up may increase the power supply current drastically, causing thermal damage to the device. For the same reason, also be careful not to let the analog power-supply voltage (AVCC, AVRH) exceed the digital power-supply voltage.
2. Treatment of unused pins
Leaving unused input pins open may result in misbehavior or latch up and possible permanent damage of the device. Therefore they must be pulled up or pulled down through resistors. In this case those resistors should be more than 2 k . Unused bidirectional pins should be set to the output state and can be left open, or the input state with the above described connection.
3. Using external clock
To use external clock, drive the X0 pin and leave X1 pin open. MB90860A Series X0 Open X1
4. Precautions for when not using a sub clock signal
If you do not connect pins X0A and X1A to an oscillator, use pull-down handling on the X0A pin, and leave the X1A pin open.
18
MB90860A Series
5. Notes on during operation of PLL clock mode
If the PLL clock mode is selected, the microcontroller attempt to be working with the self-oscillating circuit even when there is no external oscillator or external clock input is stopped. Performance of this operation, however, cannot be guaranteed.
6. Power supply pins (VCC/VSS)
* If there are multiple VCC and VSS pins, from the point of view of device design, pins to be of the same potential are connected the inside of the device to prevent such malfunctioning as latch up. To reduce unnecessary radiation, prevent malfunctioning of the strobe signal due to the rise of ground level, and observe the standard for total output current, be sure to connect the VCC and VSS pins to the power supply and ground externally. * Connect VCC and VSS to the device from the current supply source at a low impedance. * As a measure against power supply noise, connect a capacitor of about 0.1 F as a bypass capacitor between VCC and VSS in the vicinity of VCC and VSS pins of the device Vcc Vss
Vcc Vss Vcc
Vss
MB90860A Series
Vcc Vss
Vss
Vcc
7. Pull-up/down resistors
The MB90860A Series does not support internal pull-up/down resistors (Port 0 to Port 3: built-in pull-up resistors). Use external components where needed.
8. Crystal Oscillator Circuit
Noises around X0 or X1 pins may be possible causes of abnormal operations. Make sure to provide bypass capacitors via shortest distance from X0, X1 pins, crystal oscillator (or ceramic resonator) and ground lines, and make sure, to the utmost effort, that lines of oscillation circuit not cross the lines of other circuits. It is highly recommended to provide a printed circuit board art work surrounding X0 and X1 pins with a ground area for stabilizing the operation.
9. Turning-on Sequence of Power Supply to A/D Converter and Analog Inputs
Make sure to turn on the A/D converter power supply (AVCC, AVRH, AVRL) and analog inputs (AN0 to AN23) after turning-on the digital power supply (VCC) . Turn-off the digital power after turning off the A/D converter supply and analog inputs. In this case, make sure that the voltage not exceed AVRH or AVCC (turning on/off the analog and digital power supplies simultaneously is acceptable) .
10. Connection of Unused Pins of A/D Converter if A/D Converter is used
Connect unused pins of A/D converter to AVCC = VCC, AVSS = AVRH = AVRL = VSS.
19
MB90860A Series
11. Notes on Energization
To prevent the internal regulator circuit from malfunctioning, set the voltage rise time during energization at 50 s or more (0.2 V to 2.7 V)
12. Stabilization of power supply voltage
A sudden change in the supply voltage may cause the device to malfunction even within the specified VCC supply voltage operating range. Therefore, the VCC supply voltage should be stabilized. For reference, the supply voltage should be controlled so that VCC ripple variations (peak-to-peak value) at commercial frequencies (50 Hz to 60 Hz) fall below 10% of the standard VCC supply voltage and the coefficient of fluctuation does not exceed 0.1 V/ms at instantaneous power switching.
13. Initialization
In the device, there are internal registers which are initialized only by a power-on reset. To initialize these registers, turn on the power again.
14. Port 0 to port 3 output during Power-on (External-bus mode)
As shown below, when power is turned on in External-Bus mode, there is a possibility that output signal of Port 0 to Port 3 might be unstable.
VDD5
VDD3
Port0 to Port3
Port0 to 3 outputs might be unstable Port0 to 3 outputs = Hi-Z
15. Flash security Function
The security byte is located in the area of the flash memory. If protection code 01H is written in the security byte, the flash memory is in the protected state by security. Therefore please do not write 01H in this address if you do not use the security function. Please refer to following table for the address of the security byte. Flash memory size MB90F867A (S) Embedded 1 Mbit Flash Memory Address for security byte FE0001H
20
MB90860A Series
s BLOCK DIAGRAMS
MB90V340(S) X0,X1 X0A,X1A* RST Clock Controller
16LX CPU
RAM 30 K
IO Timer 0 Input Capture 8 ch Output Compare 8 ch
FRCK0
IN7 to IN0
OUT7 to OUT0
Prescaler 5 ch SOT4 to SOT0 SCK4 to SCK0 SIN4 to SIN0 AVCC AVSS AN23 to AN0 AVRH AVRL ADTG
IO Timer 1
FRCK1
UART 5 ch
CAN Controller 3 ch
RX2 to RX0 TX2 to TX0
16-bit Reload Timer 4 ch
TIN3 to TIN0 TOT3 to TOT0
10-bit ADC 24 ch AD15 to AD00 FMC-16 Bus A23 to A16 ALE RD External Bus Interface WRL WRH HRQ HAK RDY CLK INT15 to INT8 (INT15R to INT8R) INT7 to INT0
DA01, DA00
10-bit DAC 2 ch 8/16-bit PPG 16 ch I2C Interface 2 ch
PPGF to PPG0
SDA1, SDA0 SCL1, SCL0
External Interrupt
DMAC
Clock Monitor
CKOT
* : Only for MB90V340 ( without `S' Suffix ) 21
MB90860A Series
MB90F867A (S) , MB90867A (S) X0,X1 X0A,X1A* RST Clock Controller
16LX CPU
RAM 6K
IO Timer 0 Input Capture 8 ch
FRCK0
IN7 to IN0
ROM/Flash 128 K
Output Compare 8 ch IO Timer 1
OUT7 to OUT0
Prescaler 4 ch SOT3 to SOT0 SCK3 to SCK0 SIN3 to SIN0 AVCC AVSS AN15 to AN0 AN23 to AN16 AVRH AVRL ADTG
FRCK1
UART 4 ch
16-bit Reload Timer 4 ch
TIN3 to TIN0 TOT3 to TOT0
10-bit ADC 16/24 ch AD15 to AD00 FMC-16 Bus A23 to A16 ALE RD External Bus Interface WRL WRH HRQ HAK RDY CLK INT15 to INT8 (INT15R to INT8R) INT7 to INT0
PPGF to PPG0
8/16-bit PPG 16 ch I2C Interface 2 ch External Interrupt
DMAC
SDA1, SDA0 SCL1, SCL0
Clock Monitor * : Only for devices without `S' Suffix
CKOT
22
MB90860A Series
s MEMORY MAP
MB90V340 (S)
FFFFFFH FFFFFFH
MB90867A (S) MB90F867A (S) ROM(FF bank)
FF0000H FEFFFFH
ROM(FF bank)
FF0000H FEFFFFH
ROM(FE bank)
FE0000H FDFFFFH FD0000H FCFFFFH FC0000H FBFFFFH FB0000H FAFFFFH FA0000H F9FFFFH F90000H F8FFFFH F80000H 00FFFFH 007FFFH 007900H 0078FFH FE0000H
ROM(FE bank)
ROM (Image of FF bank) 008000H Peripheral
00FFFFH 008000H 007FFFH 007900H
ROM (Image of FF bank) Peripheral
RAM 30 K
0018FFH
RAM 6 K
000100H 0000EFH 000000H 000100H 0000EFH 000000H
Peripheral
Peripheral
: No access
Note : The high-order portion of bank 00 gives the image of the FF bank ROM to make the small model of the C compiler effective. Since the low-order 16 bits are the same, the table in ROM can be referenced without using the far specification in the pointer declaration. For example, an attempt to access 00C000H accesses the value at FFC000H in ROM. The ROM area in bank FF exceeds 32 Kbytes, and its entire image cannot be shown in bank 00. The image between FF8000H and FFFFFFH is visible in bank 00, while the image between FF0000H and FF7FFFH is visible only in bank FF.
23
MB90860A Series
s I/O MAP
Address 00H 01H 02H 03H 04H 05H 06H 07H 08H 09H 0AH 0BH 0CH 0DH 0EH 0FH 10H 11H 12H 13H 14H 15H 16H 17H 18H 19H 1AH 1BH 1CH 1DH 1EH 1FH Port 0 Pullup Control Register Port 1 Pullup Control Register Port 2 Pullup Control Register Port 3 Pullup Control Register Register Port 0 Data Register Port 1 Data Register Port 2 Data Register Port 3 Data Register Port 4 Data Register Port 5 Data Register Port 6 Data Register Port 7 Data Register Port 8 Data Register Port 9 Data Register Port A Data Register Port 5 Analog Input Enable Register Port 6 Analog Input Enable Register Port 7 Analog Input Enable Register Input Level Select Register 0 Input Level Select Register 1 Port 0 Direction Register Port 1 Direction Register Port 2 Direction Register Port 3 Direction Register Port 4 Direction Register Port 5 Direction Register Port 6 Direction Register Port 7 Direction Register Port 8 Direction Register Port 9 Direction Register Port A Direction Register Abbreviation PDR0 PDR1 PDR2 PDR3 PDR4 PDR5 PDR6 PDR7 PDR8 PDR9 PDRA ADER5 ADER6 ADER7 ILSR0 ILSR1 DDR0 DDR1 DDR2 DDR3 DDR4 DDR5 DDR6 DDR7 DDR8 DDR9 DDRA Reserved PUCR0 PUCR1 PUCR2 PUCR3 R/W R/W R/W R/W Port 0 Port 1 Port 2 Port 3 00000000 00000000 00000000 00000000 Access R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W Resource name Port 0 Port 1 Port 2 Port 3 Port 4 Port 5 Port 6 Port 7 Port 8 Port 9 Port A Port 5, A/D Port 6, A/D Port 7, A/D Ports Ports Port 0 Port 1 Port 2 Port 3 Port 4 Port 5 Port 6 Port 7 Port 8 Port 9 Port A Initial value XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX 11111111 11111111 11111111 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000100
(Continued)
24
MB90860A Series
Address 20H 21H 22H 23H 24H 25H 26H 27H 28H 29H 2AH 2BH 2CH 2DH 2EH 2FH 30H 31H 32H 33H 34H 35H 36H 37H 38H 39H 3AH 3BH 3CH 3DH 3EH 3FH
Register Serial Mode Register 0 Serial Control Register 0 Reception/Transmission Data Register 0 Serial Status Register 0 Extended Communication Control Reg. 0 Extended Status/Control Register 0 Baud Rate Generator Register 00 Baud Rate Generator Register 01 Serial Mode Register 1 Serial Control Register 1 Reception/Transmission Data Register 1 Serial Status Register 1 Extended Communication Control Reg. 1 Extended Status Control Register 1 Baud Rate Generator Register 10 Baud Rate Generator Register 11 PPG 0 Operation Mode Control Register PPG 1 Operation Mode Control Register PPG 01 Clock Select Register PPG 2 Operation Mode Control Register PPG 3 Operation Mode Control Register PPG 23 Clock Select Register PPG 4 Operation Mode Control Register PPG 5 Operation Mode Control Register PPG 4 and PPG 5 Clock Select Register Program Address Detection Control Status Register 1 PPG 6 Operation Mode Control Register PPG 7 Operation Mode Control Register PPG 67 Clock Select Register
Abbreviation SMR0 SCR0 RDR0/ TDR0 SSR0 ECCR0 ESCR0 BGR00 BGR01 SMR1 SCR1 RDR1/ TDR1 SSR1 ECCR1 ESCR1 BGR10 BGR11 PPGC0 PPGC1 PPG01 Reserved PPGC2 PPGC3 PPG23 Reserved PPGC4 PPGC5 PPG45 PACSR1 PPGC6 PPGC7 PPG67 Reserved
Access W, R/W W, R/W R/W R, R/W R, W, R/W R/W R/W R/W W, R/W W, R/W R/W R, R/W R, W, R/W R/W R/W R/W W, R/W W, R/W R/W W, R/W W, R/W R/W W, R/W W, R/W R/W R/W W, R/W W, R/W R/W
Resource name
Initial value 00000000 00000000 00000000
UART0
00001000 000000XX 00000100 00000000 00000000 00000000 00000000 00000000
UART1
00001000 000000XX 00000100 00000000 00000000 0X000XX1
16-bit PPG 0/1
0X000001 000000X0 0X000XX1
16-bit PPG 2/3
0X000001 000000X0 0X000XX1
16-bit PPG 4/5 Address Match Detection 1 16-bit PPG 6/7
0X000001 000000X0 00000000 0X000XX1 0X000001 000000X0
(Continued)
25
MB90860A Series
Address 40H 41H 42H 43H 44H 45H 46H 47H 48H 49H 4AH 4BH 4CH 4DH 4EH 4FH 50H 51H 52H 53H 54H 55H 56H 57H 58H 59H 5AH 5BH 5CH 5DH 5EH 5FH
Register PPG 8 Operation Mode Control Register PPG 9 Operation Mode Control Register PPG 89 Clock Select Register PPG A Operation Mode Control Register PPG B Operation Mode Control Register PPG AB Clock Select Register PPG C Operation Mode Control Register PPG D Operation Mode Control Register PPG CD Clock Select Register PPG E Operation Mode Control Register PPG F Operation Mode Control Register PPG EF Clock Select Register Input Capture Control Status Register 0/1 Input Capture Edge Register 0/1 Input Capture Control Status Register 2/3 Input Capture Edge Register 2/3 Input Capture Control Status Register 4/5 Input Capture Edge Register 4/5 Input Capture Control Status Register 6/7 Input Capture Edge Register 6/7 Output Compare Control Status Register 0 Output Compare Control Status Register 1 Output Compare Control Status Register 2 Output Compare Control Status Register 3 Output Compare Control Status Register 4 Output Compare Control Status Register 5 Output Compare Control Status Register 6 Output Compare Control Status Register 7
Abbreviation PPGC8 PPGC9 PPG89
Access W, R/W W, R/W R/W W, R/W W, R/W R/W W, R/W W, R/W R/W W, R/W W, R/W R/W R/W R/W, R R/W R R/W R R/W R/W, R R/W R/W R/W R/W R/W R/W R/W R/W
Resource name
Initial value 0X000XX1
16-bit PPG 8/9
0X000001 000000X0 0X000XX1
Reserved PPGCA PPGCB PPGAB Reserved PPGCC PPGCD PPGCD Reserved PPGCE PPGCF PPGEF Reserved ICS01 ICE01 ICS23 ICE23 ICS45 ICE45 ICS67 ICE67 OCS0 OCS1 OCS2 OCS3 OCS4 OCS5 OCS6 OCS7 Input Capture 0/1 Input Capture 2/3 Input Capture 4/5 Input Capture 6/7 Output Compare 0/1 Output Compare 2/3 Output Compare 4/5 Output Compare 6/7 00000000 XXX0X0XX 00000000 XXXXXXXX 00000000 XXXXXXXX 00000000 XXX000XX 0000XX00 0XX00000 0000XX00 0XX00000 0000XX00 0XX00000 0000XX00 0XX00000 0X000XX1 16-bit PPG E/F 0X000001 000000X0 0X000XX1 16-bit PPG C/D 0X000001 000000X0 16-bit PPG A/B 0X000001 000000X0
(Continued)
26
MB90860A Series
Address 60H 61H 62H 63H 64H 65H 66H 67H 68H 69H 6AH 6BH 6CH 6DH 6EH 6FH 70H to 8FH 90H to 9AH 9BH 9CH 9DH 9EH 9FH A0H A1H A2H, A3H A4H A5H A6H A7H A8H A9H
Register Timer Control Status Register 0 Timer Control Status Register 0 Timer Control Status Register 1 Timer Control Status Register 1 Timer Control Status Register 2 Timer Control Status Register 2 Timer Control Status Register 3 Timer Control Status Register 3 A/D Control Status Register 0 A/D Control Status Register 1 A/D Data Register 0 A/D Data Register 1 ADC Setting Register 0 ADC Setting Register 1 ROM Mirroring Register
Abbreviation TMCSR0 TMCSR0 TMCSR1 TMCSR1 TMCSR2 TMCSR2 TMCSR3 TMCSR3 ADCS0 ADCS1 ADCR0 ADCR1 ADSR0 ADSR1
Access R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R R R/W R/W W
Resource name 16-bit Reload Timer 0 16-bit Reload Timer 1 16-bit Reload Timer 2 16-bit Reload Timer 3
Initial value 00000000 XXXX0000 00000000 XXXX0000 00000000 XXXX0000 00000000 XXXX0000 000XXXX0 0000000X 00000000 XXXXXX00 00000000 00000000
A/D Converter
Reserved ROMM Reserved Reserved DMA Descriptor Channel Specification Register DMA Status Register L DMA Status Register H Program Address Detection Control Status Register 0 Delayed Interrupt/Release Low-power Mode Control Register Clock Selection Register DCSR DSRL DSRH PACSR0 DIRR LPMCR CKSCR R/W R/W R/W R/W R/W W, R/W R, R/W Address Match Detection 0 Delayed Interrupt Low Power Controller Low Power Controller DMA External Memory Access Watchdog Timer Time Base Timer DMA 00000000 00000000 00000000 00000000 XXXXXXX0 00011000 11111100 ROM Mirror XXXXXXX1
Reserved DMA Stop Status Register Automatic Ready Function Select Reg. External Address Output Control Reg. Bus Control Signal Selection Register Watchdog Control Register Timebase Timer Control Register DSSR ARSR HACR ECSR WDTC TBTC R/W W W W R, W W, R/W 00000000 0011XX00 00000000 0000000X XXXXX111 1XX00100
(Continued)
27
MB90860A Series
Address AAH ABH ACH ADH AEH AFH B0H B1H B2H B3H B4H B5H B6H B7H B8H B9H BAH BBH BCH BDH BEH BFH C0H C1H C2H C3H C4H, C5H C6H C7H C8H C9H
Register Watch Timer Control Register DMA Enable Register L DMA Enable Register H Flash Control Status Register (FlashDevices only. Otherwise reserved) Interrupt Control Register 00 Interrupt Control Register 01 Interrupt Control Register 02 Interrupt Control Register 03 Interrupt Control Register 04 Interrupt Control Register 05 Interrupt Control Register 06 Interrupt Control Register 07 Interrupt Control Register 08 Interrupt Control Register 09 Interrupt Control Register 10 Interrupt Control Register 11 Interrupt Control Register 12 Interrupt Control Register 13 Interrupt Control Register 14 Interrupt Control Register 15 D/A Converter Data 0 D/A Converter Data 1 D/A Control 0 D/A Control 1 External Interrupt Request Enable Register 0 External Interrupt Request Register 0 External Interrupt Level Register 0 External Interrupt Level Register 0
Abbreviation WTC DERL DERH FMCS
Access R, R/W R/W R/W R, R/W
Resource name Watch Timer
Initial value 1X001000 00000000 00000000 000X0000
Reserved DMA
Flash Memory
Reserved ICR00 ICR01 ICR02 ICR03 ICR04 ICR05 ICR06 ICR07 ICR08 ICR09 ICR10 ICR11 ICR12 ICR13 ICR14 ICR15 DAT0 DAT1 DACR0 DACR1 Reserved ENIR0 EIRR0 ELVR0 ELVR0 R/W R/W R/W R/W External Interrupt 0 00000000 XXXXXXXX 00000000 00000000 W, R/W W, R/W W, R/W W, R/W W, R/W W, R/W W, R/W W, R/W W, R/W W, R/W W, R/W W, R/W W, R/W W, R/W W, R/W W, R/W R/W R/W R/W R/W D/A Converter Interrupt Controller 00000111 00000111 00000111 00000111 00000111 00000111 00000111 00000111 00000111 00000111 00000111 00000111 00000111 00000111 00000111 00000111 XXXXXXXX XXXXXXXX XXXXXXX0 XXXXXXX0
(Continued)
28
MB90860A Series
Address CAH CBH CCH CDH CEH CFH D0H D1H D2H D3H D4H D5H D6H D7H D8H D9H DAH DBH DCH DDH DEH DFH E0H to EFH F0H to FFH
Register External Interrupt Request Enable Register 1 External Interrupt Request Register 1 External Interrupt Level Register 1 External Interrupt Level Register 1 External Interrupt Source Select Register PLL/Subclock Control Register DMA Buffer Address Pointer L DMA Buffer Address Pointer M DMA Buffer Address Pointer H DMA Control Register I/O Register Address Pointer L I/O Register Address Pointer H Data Counter L Data Counter H Serial Mode Register 2 Serial Control Register 2 Reception/Transmission Data Register 2 Serial Status Register 2 Extended Communication Control Register 2 Extended Status/Control Register 2 Baud Rate Reload Register 20 Baud Rate Reload Register 21
Abbreviation ENIR1 EIRR1 ELVR1 ELVR1 EISSR PSCCR BAPL BAPM BAPH DMACS IOAL IOAH DCTL DCTH SMR2 SCR2 RDR2/ TDR2 SSR2 ECCR2 ESCR2 BGR20 BGR21
Access R/W R/W R/W R/W R/W W R/W R/W R/W R/W R/W R/W R/W R/W W, R/W W, R/W R/W R, R/W R, W, R/W R/W R/W R/W
Resource name
Initial value 00000000 XXXXXXXX
External Interrupt 1
00000000 00000000 00000000
PLL
XXXX0000 XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX 00000000 00000000 00000000
DMA
UART2
00001000 000000XX 00000100 00000000 00000000
Reserved External
(Continued)
29
MB90860A Series
Address 7900H 7901H 7902H 7903H 7904H 7905H 7906H 7907H 7908H 7909H 790AH 790BH 790CH 790DH 790EH 790FH 7910H 7911H 7912H 7913H 7914H 7915H 7916H 7917H 7918H 7919H 791AH 791BH 791CH 791DH 791EH 791FH 7920H 7921H 7922H 7923H
Register Reload Register L0 Reload Register H0 Reload Register L1 Reload Register H1 Reload Register L2 Reload Register H2 Reload Register L3 Reload Register H3 Reload Register L4 Reload Register H4 Reload Register L5 Reload Register H5 Reload Register L6 Reload Register H6 Reload Register L7 Reload Register H7 Reload Register L8 Reload Register H8 Reload Register L9 Reload Register H9 Reload Register LA Reload Register HA Reload Register LB Reload Register HB Reload Register LC Reload Register HC Reload Register LD Reload Register HD Reload Register LE Reload Register HE Reload Register LF Reload Register HF Input Capture Data Register 0 Input Capture Data Register 0 Input Capture Data Register 1 Input Capture Data Register 1
Abbreviation PRLL0 PRLH0 PRLL1 PRLH1 PRLL2 PRLH2 PRLL3 PRLH3 PRLL4 PRLH4 PRLL5 PRLH5 PRLL6 PRLH6 PRLL7 PRLH7 PRLL8 PRLH8 PRLL9 PRLH9 PRLLA PRLHA PRLLB PRLHB PRLLC PRLHC PRLLD PRLHD PRLLE PRLHE PRLLF PRLHF IPCP0 IPCP0 IPCP1 IPCP1
Access R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R R R R
Resource name
Initial value XXXXXXXX
16-bit PPG 0/1
XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX
16-bit PPG 2/3
16-bit PPG 4/5
16-bit PPG 6/7
16-bit PPG 8/9
16-bit PPG A/B
16-bit PPG C/D
16-bit PPG E/F
Input Capture 0/1
(Continued)
30
MB90860A Series
Address 7924H 7925H 7926H 7927H 7928H 7929H 792AH 792BH 792CH 792DH 792EH 792FH 7930H 7931H 7932H 7933H 7934H 7935H 7936H 7937H 7938H 7939H 793AH 793BH 793CH 793DH 793EH 793FH 7940H 7941H 7942H 7943H 7944H 7945H 7946H 7947H
Register Input Capture Data Register 2 Input Capture Data Register 2 Input Capture Data Register 3 Input Capture Data Register 3 Input Capture Data Register 4 Input Capture Data Register 4 Input Capture Data Register 5 Input Capture Data Register 5 Input Capture Data Register 6 Input Capture Data Register 6 Input Capture Data Register 7 Input Capture Data Register 7 Output Compare Register 0 Output Compare Register 0 Output Compare Register 1 Output Compare Register 1 Output Compare Register 2 Output Compare Register 2 Output Compare Register 3 Output Compare Register 3 Output Compare Register 4 Output Compare Register 4 Output Compare Register 5 Output Compare Register 5 Output Compare Register 6 Output Compare Register 6 Output Compare Register 7 Output Compare Register 7 Data Register 0 Data Register 0 Control Status Register 0 Control Status Register 0 Data Register 1 Data Register 1 Control Status Register 1 Control Status Register 1
Abbreviation IPCP2 IPCP2 IPCP3 IPCP3 IPCP4 IPCP4 IPCP5 IPCP5 IPCP6 IPCP6 IPCP7 IPCP7 OCCP0 OCCP0 OCCP1 OCCP1 OCCP2 OCCP2 OCCP3 OCCP3 OCCP4 OCCP4 OCCP5 OCCP5 OCCP6 OCCP6 OCCP7 OCCP7 TCDT0 TCDT0 TCCSL0 TCCSH0 TCDT1 TCDT1 TCCSL1 TCCSH1
Access R R R R R R R R R R R R R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W
Resource name
Initial value XXXXXXXX
Input Capture 2/3
XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX 00000000 00000000 00000000 0XXXXXXX 00000000 00000000 00000000 0XXXXXXX
Input Capture 4/5
Input Capture 6/7
Output Compare 0/1
Output Compare 2/3
Output Compare 4/5
Output Compare 6/7
I/O Timer 0
I/O Timer 1
(Continued)
31
MB90860A Series
Address 7948H 7949H 794AH 794BH 794CH 794DH 794EH 794FH 7950H 7951H 7952H 7953H 7954H 7955H 7956H 7957H 7958H 7959H 795AH 795BH 795CH 795DH 795EH 795FH 7960H to 796BH 796CH 796DH to 796FH
Register Timer Register 0/Reload Register 0 Timer Register 1/Reload Register 1 Timer Register 2/Reload Register 2 Timer Register 3/Reload Register 3 Serial Mode Register 3 Serial Control Register 3 Reception/Transmission Data Register 3 Serial Status Register 3 Extended Communication Control Reg. 3 Extended Status/Control Register 3 Baud Rate Reload Register 30 Baud Rate Reload Register 31 Serial Mode Register 4 Serial Control Register 4 Reception/Transmission Data Register 4 Serial Status Register 4 Extended Communication Control Reg. 4 Extended Status/Control Register 4 Baud Rate Reload Register 40 Baud Rate Reload Register 41
Abbreviation TMR0/ TMRLR0 TMR1/ TMRLR1 TMR2/ TMRLR2 TMR3/ TMRLR3 SMR3 SCR3 RDR3/ TDR3 SSR3 ECCR3 ESCR3 BGR30 BGR31 SMR4 SCR4 RDR4/ TDR4 SSR4 ECCR4 ESCR4 BGR40 BGR41 Reserved
Access R/W R/W R/W R/W R/W R/W R/W R/W W, R/W W, R/W R/W R, R/W R, W, R/W R/W R/W R/W W, R/W W, R/W R/W R, R/W R, W, R/W R/W R/W R/W
Resource name 16-bit Reload Timer 0 16-bit Reload Timer 1 16-bit Reload Timer 2 16-bit Reload Timer 3
Initial value XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX 00000000 00000000 00000000
UART3
00001000 000000XX 00000100 00000000 00000000 00000000 00000000 00000000
UART4
00001000 000000XX 00000100 00000000 00000000
Clock Output Enable Register
CLKR Reserved
R/W
Clock Monitor
XXXX0000
(Continued)
32
MB90860A Series
Address 7970H 7971H 7972H 7973H 7974H 7975H 7976H 7977H 7978H 7979H, 797AH 797BH 797CH to 797FH 7980H 7981H 7982H 7983H 7984H 7985H 7986H 7987H 7988H 7989H, 798AH 798BH 798CH to 79C1H 79C2H 79C3H to 79DFH
Register I2C Bus Status Register 0 I C Bus Control Register 0 I2C 10-bit Slave Address Register 0 I2C 10-bit Slave Address Mask Register 0 I C 7-bit Slave Address Register 0 I C 7-bit Slave Address Mask Register 0 I C Data Register 0
2 2 2 2
Abbreviation IBSR0 IBCR0 ITBAL0 ITBAH0 ITMKL0 ITMKH0 ISBA0 ISMK0 IDAR0 Reserved
Access R W, R/W R/W R/W R/W R/W R/W R/W R/W
Resource name
Initial value 00000000 00000000 00000000 00000000
I2C Interface 0
11111111 00111111 00000000 01111111 00000000
I2C Clock Control Register 0
ICCR0 Reserved
R/W
I2C Interface 0
00011111
I2C Bus Status Register 1 I2C Bus Control Register 1 I2C 10-bit Slave Address Register 1 I2C 10-bit Slave Address Mask Register 1 I C 7-bit Slave Address Register 1 I2C 7-bit Slave Address Mask Register 1 I2C Data Register 1
2
IBSR1 IBCR1 ITBAL1 ITBAH1 ITMKL1 ITMKH1 ISBA1 ISMK1 IDAR1 Reserved
R W, R/W R/W R/W R/W R/W R/W R/W R/W I C Interface 1
2
00000000 00000000 00000000 00000000 11111111 00111111 00000000 01111111 00000000
I2C Clock Control Register 1
ICCR1 Reserved
R/W
I2C Interface 1
00011111
Clock Modulator Control Register
CMCR Reserved
R, R/W
Clock Modulator
0001X000
(Continued)
33
MB90860A Series
(Continued)
Address 79E0H 79E1H 79E2H 79E3H 79E4H 79E5H 79E6H 79E7H 79E8H 79E9H to 79EFH 79F0H 79F1H 79F2H 79F3H 79F4H 79F5H 79F6H 79F7H 79F8H 79F9H to 7FFFH Program Address Detection Register 3 Program Address Detection Register 3 Program Address Detection Register 3 Program Address Detection Register 4 Program Address Detection Register 4 Program Address Detection Register 4 Program Address Detection Register 5 Program Address Detection Register 5 Program Address Detection Register 5 Register Program Address Detection Register 0 Program Address Detection Register 0 Program Address Detection Register 0 Program Address Detection Register 1 Program Address Detection Register 1 Program Address Detection Register 1 Program Address Detection Register 2 Program Address Detection Register 2 Program Address Detection Register 2 Abbreviation PADR0 PADR0 PADR0 PADR1 PADR1 PADR1 PADR2 PADR2 PADR2 Reserved PADR3 PADR3 PADR3 PADR4 PADR4 PADR4 PADR5 PADR5 PADR5 Reserved R/W R/W R/W R/W R/W R/W R/W R/W R/W Address Match Detection 1 XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX Access R/W R/W R/W R/W R/W R/W R/W R/W R/W Address Match Detection 0 Resource name Initial value XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX
Notes : * Initial value of "X" represents unknown value. * Addresses in the range 0000H to 00BFH, which are not listed in the table, are reserved for the primary functions of the MCU. A read access to these reserved addresses results reading "X" and any write access should not be performed.
34
MB90860A Series
s INTERRUPT FACTORS, INTERRUPT VECTORS, INTERRUPT CONTROL REGISTER
Interrupt cause Reset INT9 instruction Exception (Reserved) (Reserved) Input Capture 6 Input Capture 7 I2C0 (Reserved) 16-bit Reload Timer 0 16-bit Reload Timer 1 16-bit Reload Timer 2 16-bit Reload Timer 3 PPG 0/1/4/5 PPG 2/3/6/7 PPG 8/9/C/D PPG A/B/E/F Time Base Timer External Interrupt 0 to 3, 8 to 11 Watch Timer External Interrupt 4 to 7, 12 to 15 A/D Converter I/O Timer 0 / I/O Timer 1 Input Capture 4/5 / I2C1 Output Compare 0/1/4/5 Input Capture 0 to 3 Output Compare 2/3/6/7 UART 0 RX UART 0 TX UART 1 RX / UART 3 RX UART 1 TX / UART 3 TX EI2OS clear N N N N N Y1 Y1 N N Y1 Y1 Y1 Y1 N N N N N Y1 N Y1 Y1 N Y1 Y1 Y1 Y1 Y2 Y1 Y2 Y1 DMA ch number 0 1 2 3 4 5 6 7 8 9 10 11 12 13 Interrupt vector Number #08 #09 #10 #11 #12 #13 #14 #15 #16 #17 #18 #19 #20 #21 #22 #23 #24 #25 #26 #27 #28 #29 #30 #31 #32 #33 #34 #35 #36 #37 #38 Address FFFFDCH FFFFD8H FFFFD4H FFFFD0H FFFFCCH FFFFC8H FFFFC4H FFFFC0H FFFFBCH FFFFB8H FFFFB4H FFFFB0H FFFFACH FFFFA8H FFFFA4H FFFFA0H FFFF9CH FFFF98H FFFF94H FFFF90H FFFF8CH FFFF88H FFFF84H FFFF80H FFFF7CH FFFF78H FFFF74H FFFF70H FFFF6CH FFFF68H FFFF64H Interrupt control register Number ICR00 ICR01 ICR02 ICR03 ICR04 ICR05 ICR06 ICR07 ICR08 ICR09 ICR10 ICR11 ICR12 ICR13 Address 0000B0H 0000B1H 0000B2H 0000B3H 0000B4H 0000B5H 0000B6H 0000B7H 0000B8H 0000B9H 0000BAH 0000BBH 0000BCH 0000BDH
(Continued)
35
MB90860A Series
(Continued)
Interrupt cause UART 2 RX / UART 4 RX UART 2 TX / UART 4 TX Flash Memory Delayed interrupt Y1 : Usable Y2 : Usable, with EI2OS stop function N : Unusable Notes : * The peripheral resources sharing the ICR register have the same interrupt level. * When two peripheral resources share the ICR register, only one can use Extended Intelligent I/O Service at a time. * When either of the two peripheral resources sharing the ICR register specifies Extended Intelligent I/O Service, the other one cannot use interrupts. EI2OS clear Y2 Y1 N N DMA ch number 14 15 Interrupt vector Number #39 #40 #41 #42 Address FFFF60H FFFF5CH FFFF58H FFFF54H Interrupt control register Number ICR14 ICR15 Address 0000BEH 0000BFH
36
MB90860A Series
s ELECTRICAL CHARACTERISTICS
1. Absolute Maximum Ratings
Parameter Symbol VCC Power supply voltage AVCC AVRH, AVRL Input voltage Output voltage Maximum Clamp Current Total Maximum Clamp Current "L" level maximum output current "L" level average output current "L" level maximum overall output current "L" level average overall output current "H" level maximum output current "H" level average output current "H" level maximum overall output current "H" level average overall output current Power consumption Operating temperature Storage temperature VI VO ICLAMP |ICLAMP| IOL IOLAV IOL IOLAV IOH IOHAV IOH IOHAV PD TA TSTG Rating Min VSS - 0.3 VSS - 0.3 VSS - 0.3 VSS - 0.3 VSS - 0.3 -4.0 -40 -55 Max VSS + 6.0 VSS + 6.0 VSS + 6.0 VSS + 6.0 VSS + 6.0 +4.0 40 15 4 100 50 -15 -4 -100 -50 340 +105 +150 Unit V V V V V mA mA mA mA mA mA mA mA mA mA C C VCC = AVCC *1 AVCC AVRH, AVCC AVRL, AVRH AVRL *2 *2 *4 *4 *3 *3 *3 *3 *3 *3 *3 *3 (VSS = AVSS = 0 V) Remarks
mW MB90F867A
(Continued)
37
MB90860A Series
(Continued)
*1: Set AVCC and VCC to the same voltage. Make sure that AVCC does not exceed VCC and that the voltage at the analog inputs does not exceed AVCC when the power is switched on. *2: VI and VO should not exceed VCC + 0.3 V. VI should not exceed the specified ratings. However if the maximun current to/from an input is limited by some means with external components, the ICLAMP rating supercedes the VI rating. *3: Applicable to pins: P00 to P07, P10 to P17, P20 to P27, P30 to P37, P40 to P47, P50 to P57, P60 to P67, P70 to P77, P80 to P87, P90 to P97, PA0 to PA1 *4: * Applicable to pins: P00 to P07, P10 to P17, P20 to P27, P30 to P37, P40 to P47, P50 to P57, P60 to P67 P70 to P77, P80 to P87, P90 to P97, PA0 to PA1 * Use within recommended operating conditions. * Use at DC voltage (current) * The +B signal should always be applied a limiting resistance placed between the +B signal and the microcontroller. * The value of the limiting resistance should be set so that when the +B signal is applied the input current to the microcontroller pin does not exceed rated values, either instantaneously or for prolonged periods. * Note that when the microcontroller drive current is low, such as in the power saving modes, the +B input potential may pass through the protective diode and increase the potential at the VCC pin, and this may affect other devices. * Note that if a +B signal is input when the microcontroller power supply is off (not fixed at 0 V) , the power supply is provided from the pins, so that incomplete operation may result. * Note that if the +B input is applied during power-on, the power supply is provided from the pins and the resulting supply voltage may not be sufficient to operate the power-on reset. * Care must be taken not to leave the +B input pin open. * Sample recommended circuits: * Input/output equivalent circuits
Protective diode
VCC
Limiting resistance +B input (0 V to 16 V)
P-ch
N-ch
R
WARNING: Semiconductor devices can be permanently damaged by application of stress (voltage, current, temperature, etc.) in excess of absolute maximum ratings. Do not exceed these ratings.
38
MB90860A Series
2. Recommended Conditions
Value Min 4.0 VCC, AVCC 3.5 4.5 3.0 Typ 5.0 5.0 5.0 Max 5.5 5.5 5.5 5.5
(VSS = AVSS = 0 V) Unit V V V V F C Remarks Under normal operation Under normal operation, when not using the A/D converter and not Flash programming. When External bus is used. Maintains RAM data in stop mode Use a ceramic capacitor or capacitor of better AC characteristics. Capacitor at the VCC should be greater than this capacitor.
Parameter
Symbol
Power supply voltage
Smooth capacitor
CS
0.1 -40
1.0 +105
Operating temperature
TA
C
CS
C Pin Connection Diagram
WARNING: The recommended operating conditions are required in order to ensure the normal operation of the semiconductor device. All of the device's electrical characteristics are warranted when the device is operated within these ranges. Always use semiconductor devices within their recommended operating condition ranges. Operation outside these ranges may adversely affect reliability and could result in device failure. No warranty is made with respect to uses, operating conditions, or combinations not represented on the data sheet. Users considering application outside the listed conditions are advised to contact their FUJITSU representatives beforehand.
39
MB90860A Series
3. DC Characteristics
Parameter Symbol Pin Condition
(TA = -40 C to +105 C, VCC = 5.0 V 10%, VSS = AVSS = 0 V) Value Min Typ Max VCC + 0.3 Unit Remarks Port inputs if CMOS hysteresis input levels are selected (except UART SIN input pins and I2C input pins) Port inputs if AUTOMOTIVE input levels are selected Port inputs if TTL input levels are selected UART SIN inputs if CMOS input levels are selected I2C Port inputs if CMOS hysteresis input levels are selected RST input pin (CMOS hysteresis) MD input pin Port inputs if CMOS hysteresis input levels are selected (except UART SIN input pins and I2C input pins) Port inputs if AUTOMOTIVE input levels are selected Port inputs if TTL input levels are selected UART SIN inputs if CMOS input levels are selected I2C Port inputs if CMOS hysteresis input levels are selected RST input pin (CMOS hysteresis) MD input pin
VIHS
0.8 VCC
V
VIHA Input H voltage (At VCC = 5 V 10%) VIHT VIHS

0.8 VCC 2.0 0.7 VCC

VCC + 0.3 VCC + 0.3 VCC + 0.3 VCC + 0.3 VCC + 0.3 VCC + 0.3
V V V
VIHI VIHR VIHM
0.7 VCC 0.8 VCC VCC - 0.3 VSS - 0.3
V V V
VILS
0.2 VCC
V
VILA Input L voltage (At VCC = 5 V 10%) VILT VILS
Normal outputs

VSS - 0.3 VSS - 0.3 VSS - 0.3 VSS - 0.3 VSS - 0.3 VSS - 0.3

0.5 VCC 0.8 0.3 VCC
V V V
VILI VILR VILM Output H voltage Output H voltage Output L voltage Output L voltage 40 VOH VOHI VOL VOLI
0.3 VCC 0.2 VCC VSS + 0.3 0.4 0.4
V V V V V V V
VCC = 4.5 V, VCC - 0.5 IOH = -4.0 mA
I2C current VCC = 4.5 V, VCC - 0.5 outputs IOH = -3.0 mA Normal outputs VCC = 4.5 V, IOL = 4.0 mA
I2C current VCC = 4.5 V, outputs IOL = 3.0 mA
(Continued)
MB90860A Series
(Continued)
Parameter Input leak current Pull-up resistance Pull-down resistance Symbol IIL Pin P00 to P07, P10 to P17, P20 to P27, P30 to P37, RST MD2 (TA = -40 C to +105, VCC = 5.0 V 10%, VSS = AVSS = 0 V) Condition VCC = 5.5 V, VSS < VI < VCC Value Min -1 Typ Max 1 Unit A Remarks
RUP
25
50
100
k
RDOWN
VCC = 5.0 V, Internal frequency : 24 MHz, At normal operation.
25
50 55
100 70
k
Except Flash devices
mA MB90F867A
ICC
VCC = 5.0 V, Internal frequency : 24 MHz, At writing FLASH memory. VCC = 5.0 V, Internal frequency : 24 MHz, At erasing FLASH memory.
70
85
mA MB90F867A
75
90
mA MB90F867A
ICCS
VCC = 5.0 V, Internal frequency : 24 MHz, At Sleep mode. VCC = 5.0 V, Internal frequency : 2 MHz, At Main Timer mode VCC VCC = 5.0 V, Internal frequency : 24 MHz, At PLL Timer mode, external frequency = 4 MHz VCC = 5.0V Internal frequency: 8 kHz, At sub operation TA = +25C VCC = 5.0V Internal frequency: 8 kHz, At sub sleep TA = +25C VCC = 5.0V Internal frequency: 8 kHz, At watch mode TA = +25C VCC = 5.0 V, At Stop mode, TA = +25C Other than C, AVCC, AVSS, AVRH, AVRL, VCC, VSS,
25
35
mA MB90F867A
ICTS
0.3
0.8
mA MB90F867A
Power supply current*
ICTSPLL6
4
7
mA MB90F867A
ICCL
170
360
A MB90F867A
ICCLS
20
50
A MB90F867A
ICCT
10
35
A MB90F867A
ICCH Input capacity CIN

7 5
25 15
A MB90F867A pF
* : Current values are tentative. They are subject to change without notice according to improvements in the characteristics. The power supply current is measured with an external clock.
41
MB90860A Series
4. AC Characteristics
(1) Clock Timing (TA = -40 C to +105 C, VCC = 5.0 V 10%, VSS = AVSS = 0 V) Symbol Pin X0, X1 Clock frequency fC X0 fCL X0A, X1A X0, X1 Clock cycle time tCYL X0 tCYLL Input clock pulse width Input clock rise and fall time Internal operating clock frequency (machine clock) Internal operating clock cycle time (machine clock) PWH, PWL PWHL, PWLL tCR, tCF fCP fCPL tCP tCPL X0A, X1A X0 X0A X0 41.67 20 41.67 10 10 5 1.5 30.5 15.2 8.192 122.1 333 -- 5 24 50 666 ns s ns s ns MHz kHz ns s Duty ratio is about 30% to 70%. When using external clock When using main clock When using sub clock When using main clock When using sub clock 3 -- 62.5 32.768 24 100 333 MHz kHz ns When using an oscillation circuit When using an external clock Value Min 3 Typ Max 16 Unit MHz Remarks When using an oscillation circuit When using an external clock*
Parameter
* : Whem selecting the PLL clock, the range of clock frequency is limitted. Use this product within range as mentioned in "Relation among external clock frequency and machine clock frequency".
tCYL
X0
PWH tCF PWL tCR
0.8 VCC 0.2 VCC
tCYLL
X0A
PWHL tCF PWLL tCR
0.8 VCC 0.2 VCC
Clock Timing 42
MB90860A Series
* Guaranteed PLL operation range
Guaranteed operation range Guaranteed PLLL operation range (CS2=1) Power supply voltage VCC (V) 5.5 4.5 3.5 Guaranteed PLL operation range (CS=0) Guaranteed A/D converter operation range
1.5
4
8
Machine clock fCP (MHz)
20
24
Guaranteed operation range of MB90860A Series CS2 (bit0 in PSCCR reigster) = 0
Machine clock fCP (MHz) x4 x3 (CS=11) (CS=10) 20 16 12 8 4.0 1.5 34 8 12 External clock fC (MHz)
1
x2 (CS=01)
Guaranteed operation frequency range*2 x1 (CS=00)
x1/2 (PLL off)
16
20
24
CS2 (bit0 in PSCCR reigster) = 1
24 Machine clock fCP (MHz) x6 x4 (CS=10) (CS=01) x2 (CS=00)
Guaranteed operation frequency range*2
16 12 8 4.0 1.5 34 8 12 External clock fC (MHz) 16
1
x1/2 (PLL off)
24
*1 : PLL x 1 guaranteed operation range is from 4.0 MHz to 20 MHz. *2 : When using a crystal oscillator or ceramic oscillator, the maximum oscillation clock frequency is 16 MHz. External clock frequency and Machine clock frequency 43
MB90860A Series
(2) Reset Standby Input
(TA = -40 C to +105 C, VCC = 5.0 V 10%, VSS = AVSS = 0.0 V) Pin Value Min 500 Max Unit ns ns s Remarks Under normal operation In Stop mode, Sub Clock mode, Sub Sleep mode and Watch mode In Time Timer mode
Parameter
Symbol
Reset input time
tRSTL
RST
Oscillation time of oscillator* + 100 s 100
* : Oscillation time of oscillator is the time that the amplitude reaches 90%. In the crystal oscillator, the oscillation time is between several ms and to tens of ms. In FAR / ceramic oscillators, the oscillation time is between hundreds of s to several ms. With an external clock, the oscillation time is 0 ms.
Under normal operation: tRSTL RST
0.2 VCC
0.2 VCC
In Stop mode, Sub Clock mode, Sub Sleep mode, Watch mode:
tRSTL
RST
0.2 VCC 90% of amplitude 0.2 VCC
X0
Internal operation clock
Oscillation time of oscillator
100 ms Oscillation stabilization waiting time Instruction execution
Internal reset
44
MB90860A Series
(3) Power On Reset
(TA = -40 C to +105 C, VCC = 5.0 V 10%, VSS = AVSS = 0.0 V) Pin VCC VCC Condition Value Min 0.05 1 Max 30 Unit ms ms Due to repetitive operation Remarks
Parameter Power on rise time Power off time
Symbol tR tOFF
tR 2.7 V 0.2 V 0.2 V tOFF If you change the power supply voltage too rapidly, a power on reset may occur. We recommend that you startup smoothly by restraining voltages when changing the power supply voltage during operation, as shown in the figure below. Perform while not using the PLL clock. However, if voltage drops are within 1 V/s, you can operate while using the PLL clock. 0.2 V
VCC
VCC 3V VSS
Holds RAM data We recommend a rise of 50 mV/ms maximum.
45
MB90860A Series
(4) Bus Timing (Read)
Parameter ALE pulse width Valid address ALE time ALE Address valid time Valid address RD time Valid address Valid data input RD pulse width RD Valid data input RD Data hold time RD ALE time RD Address valid time Valid address CLK time RD CLK time ALE RD time
(TA = -40C to +85C, VCC = 4.5 V to 5.5 V, VSS = 0.0 V, Machine Clock 16 MHz) Value SymPin Condition Unit Remarks bol Min Max tLHLL tAVLL ALE ALE, A23 to A16, AD15 to AD00 ALE, AD15 to AD00 A23 toA16, AD15 to AD00, RD A23 to A16, AD15 to AD00 RD RD, AD15 to AD00 RD, AD15 to AD00 RD, ALE RD, A23 to A16 A23 to A16, AD15 to AD00, CLK RD, CLK ALE, RD tCP/2 - 10 tCP/2 - 15 tCP/2 - 15 tCP - 15 ns ns
tLLAX
ns
tAVRL
ns
tAVDV tRLRH tRLDV tRHDX tRHLH tRHAX
3 tCP/2 - 20 0 tCP/2 - 15 tCP/2 - 10 tCP/2 - 15 tCP/2 - 15 tCP/2 - 15
5 tCP/2 - 40 3 tCP/2 - 50
ns ns ns ns ns ns
tAVCH tRLCH tLLRL
ns ns ns
46
MB90860A Series
tAVCH CLK 2.4 V
tRLCH 2.4 V
tAVLL ALE 2.4 V tLHLL tAVRL RD
tLLAX 2.4 V 0.8 V tRLRH 2.4 V 0.8 V tLLRL
tRHLH 2.4 V
tRHAX A23 to A16 2.4 V 0.8 V tRLDV tAVDV AD15 to AD00 2.4 V 0.8 V 2.4 V Address 0.8 V VIH VIL Read data 2.4 V 0.8 V tRHDX VIH VIL
47
MB90860A Series
(5) Bus Timing (Write)
Parameter
(TA = -40C to +85C, VCC = 4.5 V to 5.5 V, VSS = 0.0 V, Machine Clock 16 MHz) Value Symbol Pin Condition Unit Remarks Min Max tAVWL tWLWH tDVWH tWHDX tWHAX tWHLH tWLCH A23 to A16, AD15 to AD00, WR WR AD15 to AD00, WR AD15 to AD00, WR A23 to A16, WR WR, ALE WR, CLK tCP-15 3 tCP/2 - 20 3 tCP/2 - 20 15 tCP/2 - 10 tCP/2 - 15 tCP/2 - 15 ns ns ns ns ns ns ns
Valid address WR time WR pulse width Valid data output WR time WR Data hold time WR Address valid time WR ALE time WR CLK time
tWLCH 2.4 V
CLK
tWHLH ALE 2.4 V
tAVWL WR (WRL, WRH) 0.8 V
tWLWH 2.4 V
tWHAX A23 to A16 2.4 V 0.8 V tDVWH AD15 to AD00 2.4 V 0.8 V 2.4 V Address 0.8 V Write data 2.4 V 0.8 V tWHDX 2.4 V 0.8 V
48
MB90860A Series
(6) Ready Input Timing
Parameter RDY setup time RDY hold time
(TA = -40C to +85C, VCC = 4.5 V to 5.5 V, VSS = 0.0 V, Machine Clock 16 MHz) Value SymTest Pin Units Remarks bol Condition Min Max tRYHS tRYHH RDY RDY 45 0 ns ns
Note : If the RDY setup time is insufficient, use the auto-ready function.
CLK
2.4 V
ALE
RD/WR
tRYHS RDY When WAIT is not used. VIH
tRYHH VIH
RDY When WAIT is used.
VIL
49
MB90860A Series
(7) Hold Timing
Parameter Pin floating HAK time HAK time Pin valid time
(TA = -40C to +85C, VCC = 4.5 V to 5.5 V, VSS = 0.0 V, Machine Clock 16 MHz) Value Symbol Pin Condition Units Remarks Min Max tXHAL tHAHV HAK HAK tCP 2 tCP ns 30 tCP ns
Note : There is more than 1 cycle from when HRQ reads in until the HAK is changed.
HAK 0.8V tXHAL Each pin 2.4V 0.8V High-Z
2.4V
tHAHV 2.4V 0.8V
50
MB90860A Series
(8) UART0/1/2/3/4
Parameter Serial clock cycle time SCK SOT delay time Valid SIN SCK SCK Valid SIN hold time Serial clock "H" pulse width Serial clock "L" pulse width SCK SOT delay time Valid SIN SCK SCK Valid SIN hold time
Symbol tSCYC tSLOV tIVSH tSHIX tSHSL tSLSH tSLOV tIVSH tSHIX
Pin
(TA = -40 C to +105 C, VCC = 4.5 V to 5.5 V, VSS = 0 V) Value Condition Unit Remarks Min Max 8 tCP -80 100 60 4 tCP 4 tCP 60 60 +80 150 ns ns ns ns ns ns ns ns ns
SCK0 to SCK4 SCK0 to SCK4, SOT0 to SOT4 Internal clock operation output SCK0 to SCK4, pins are SIN0 to SIN4 CL = 80 pF + 1 TTL. SCK0 to SCK4, SIN0 to SIN4 SCK0 to SCK4 SCK0 to SCK4 SCK0 to SCK4, External clock SOT0 to SOT4 operation output pins are SCK0 to SCK4, CL = 80 pF + 1 TTL. SIN0 to SIN4 SCK0 to SCK4, SIN0 to SIN4
Notes : * AC characteristic in CLK synchronized mode. * CL is load capacity value of pins when testing. * tCP is the machine cycle (Unit : ns)
tSCYC SCK 2.4 V 0.8 V tSLOV SOT 2.4 V 0.8 V tIVSH SIN VIH VIL tSHIX VIH VIL 0.8 V
Internal Shift Clock Mode
51
MB90860A Series
tSLSH SCK VIL tSLOV SOT 2.4 V 0.8 V tIVSH SIN VIH VIL VIL VIH
tSHSL VIH
tSHIX VIH VIL
External Shift Clock Mode
(9) Trigger Input Timing
Parameter
Symbol tTRGH tTRGL
Pin INT0 to INT15, INT0R to INT15R, ADTG
(TA = -40 C to +105 C, VCC = 4.5 V to 5.5 V, VSS = 0 V) Value Condition Unit Remarks Min Max 5 tCP ns
Input pulse width
VIH
VIH VIL tTRGH tTRGL VIL
INT0 to INT15, INT0R to INT15R, ADTG
52
MB90860A Series
(10) Timer Related Resource Input Timing
Parameter Input pulse width
Symbol tTIWH tTIWL
Pin TIN0 to TIN3 IN0 to IN7
(TA = -40 C to +105 C, VCC = 4.5 V to 5.5 V, VSS = 0 V) Value Condition Unit Remarks Min Max 4 tCP ns
VIH
VIH VIL tTIWH tTIWL VIL
TIN0 to TIN3, IN0 to IN7
(11) Timer Related Resource Output Timing (TA = -40 to +105C, VCC = 4.5 V to 5.5 V, VSS = 0.0 V) Value Condition Unit Remarks Min Max 30 ns
Parameter CLK TOUT change time
Symbol tTO
Pin TOT0 to TOT3, PPG0 to PPGF
CLK
2.4 V
TOT0 to TOT3, PPG0 to PPGF
tTO
2.4 V 0.8 V
53
MB90860A Series
(12) I2C Timing (TA = -40C to +105C, VCC = 4.5 V to 5.5 V, VSS = 0.0 V) Standard-mode Fast-mode*4 Unit Symbol Condition Min Max Min Max fSCL tHDSTA tLOW tHIGH tSUSTA tHDDAT tSUDAT tSUSTO tBUS R = 1.7 k, C = 50 pF*1 0 4.0 4.7 4.0 4.7 0 250 4.0 4.7 100 3.45*2 0 0.6 1.3 0.6 0.6 0 100 0.6 1.3 400 0.9*3 kHz s s s s s ns s s
Parameter SCL clock frequency Hold time (repeated) START condition SDA SCL "L" width of the SCL clock "H" width of the SCL clock Set-up time for a repeated START condition SCL SDA Data hold time SCL SDA Data set-up time SDA SCL Set-up time for STOP condition SCL SDA Bus free time between a STOP and START condition
*1 : R, C : Pull-up resistor and load capacitor of the SCL and SDA lines. *2 : The maximum tHDDAT only has to be met if the device does not stretch the "L" width (tLOW) of the SCL signal. *3 : A Fast-mode I2C-bus device can be used in a Standard-mode I2C-bus system, but the requirement tSUDAT 250 ns must then be met. *4 : For use at over 100 kHz, set the machine clock to at least 6 MHz.
SDA tBUS
tLOW SCL
tSUDAT
tHDSTA
tHDSTA
tHDDAT
tHIGH
tSUSTA
tSUSTO
54
MB90860A Series
5. A/D Converter
(TA = -40 C to +105 C, 3.0 V AVRH - AVRL, VCC = AVCC = 5.0 V 10%, VSS = AVSS = 0 V) Pin Value Min Typ Max 10 3.0 2.5 1.9 Unit bit LSB LSB LSB Remarks
Parameter Resolution Total error Nonlinearity error Differential nonlinearity error Zero reading voltage Full scale reading voltage Compare time Sampling time Analog port input current Analog input voltage range Reference voltage range Power supply current Reference voltage current Offset between input channels
Symbol VOT VFST IAIN VAIN IA IAH IR IRH
AN0 to AN23 AVRL - 1.5 AVRL + 0.5 AVRL + 2.5 LSB AN0 to AN23 AVRH - 3.5 AVRH - 1.5 AVRH + 0.5 LSB AN0 to AN23 AN0 to AN23 AVRH AVRL AVCC AVCC AVRH AVRH AN0 to AN23 1.0 2.0 0.5 1.2 -0.3 AVRL AVRL + 2.7 0 3.5 600 16,500 s s A V V V mA A A A LSB * * 4.5 V AVCC 5.5 V 4.0 V AVCC < 4.5 V 4.5 V AVCC 5.5 V 4.0 V AVCC < 4.5 V
+0.3 AVRH AVCC AVRH - 2.7 7.5 5 900 5 4
* : When not operating A/D converter, this is the current (VCC = AVCC = AVRH = 5.0 V) . Note : The accuracy gets worse as AVRH - AVRL becomes smaller.
55
MB90860A Series
6. Definition of A/D Converter Terms
Resolution Non linearity error Differential linearity error Total error Zero reading voltage Full scale reading voltage : Analog variation that is recognized by an A/D converter. : Deviation between a line across zero-transition line ( "00 0000 0000" "00 0000 0001" ) and full-scale transition line ( "11 1111 1110" "11 1111 1111" ) and actual conversion characteristics. : Deviation of input voltage, which is required for changing output code by 1 LSB, from an ideal value. : Difference between an actual value and an ideal value. A total error includes zero transition error, full-scale transition error, and linear error. : Input voltage which results in the minimum conversion value. : Input voltage which results in the maximum conversion value.
Total error
3FF 3FE 3FD Digital output {1 LSB x (N - 1) + 0.5 LSB} Actual conversion characteristics 1.5 LSB
004 003 002 001 0.5 LSB AVRL Analog input
VNT (Actually-measured value) Actual conversion characteristics Ideal characteristics
AVRH
Total error of digital output "N" =
VNT - {1 LSB x (N - 1) + 0.5 LSB} 1 LSB AVRH - AVRL 1 LSB = (Ideal value) [V] 1024 VOT (Ideal value) = AVRL + 0.5 LSB [V]
[LSB]
VFST (Ideal value) = AVRH - 1.5 LSB [V] VNT : A voltage at which digital output transitions from (N - 1) to N.
(Continued)
56
MB90860A Series
(Continued)
Non linearity error
3FF 3FE 3FD Digital output Actual conversion characteristics {1 LSB x (N - 1) + VOT } N+1 VFST (actual measurement value) VNT (actual measurement value) Actual conversion characteristics Actual conversion characteristics
Differential linearity error
Ideal characteristics
Digital output
N
004 003 002
N-1
V (N + 1) T (actual measurement value) VNT (actual measurement value) Actual conversion characteristics AVRH Analog input
Ideal characteristics 001 VOT (actual measurement value) AVRL Analog input AVRH
N-2
AVRL
Non linearity error of digital output N = Differential linearity error of digital output N = 1 LSB =
VNT - {1 LSB x (N - 1) + VOT} 1 LSB V (N+1) T - VNT 1 LSB VFST - VOT 1022 -1 LSB [LSB] [V]
[LSB]
VOT : Voltage at which digital output transits from "000H" to "001H." VFST : Voltage at which digital output transits from "3FEH" to "3FFH."
57
MB90860A Series
7. Notes on A/D Converter Section
Use the device with external circuits of the following output impedance for analog inputs : Recommended output impedance of external circuits are : Approx. 1.5 k or lower (4.0 V AVCC 5.5 V, sampling period 0.5 s) if the output inpedance exceeds 1.5 k, set a longer sampling time or add an external capacitor compensate the output inpedance. About setting of sampling time, please refer to hardware manual of MB90860A series. If an external capacitor is used, in consideration of the effect by tap capacitance caused by external capacitors and on-chip capacitors, capacitance of the external one is recommended to be several thousand times as high as internal capacitor. If output impedance of an external circuit is too high, a sampling period for an analog voltage may be insufficient. * Analog input circuit model
Analog input R Comparator
C
4.5 V AVCC 5.5 V : R = 2.52 k, C = 10.7 pF : : 4.0 V AVCC < 4.5 V : R = 13.6 k, C = 10.7 pF : :
Note : Use the values in the figure only as a guideline.
8. Flash Memory Program/Erase Characteristics
Parameter Sector erase time Chip erase time Word (16 bit width) programming time Programs/Erase cycle Flash Data Retention Time Average TA = +85 C TA = +25 C VCC = 5.0 V Conditions Value Min 10,000 20 Typ 1 9 16 Max 15 3,600 Unit s s s cycle Year * Remarks Excludes programming prior to erasure Excludes programming prior to erasure Except for the over head time of the system
* : This value comes from the technology qualification (using Arrhenius equation to translate high temperature measurements into normalized value at + 85 C) .
58
MB90860A Series
s ORDERING INFORMATION
Part number MB90F867APF MB90F867ASPF MB90867APF MB90867ASPF MB90F867APFV MB90F867ASPFV MB90867APFV MB90867ASPFV MB90V340 MB90V340S 299-pin Ceramic PGA (PGA-299C-A01) For evaluation 100-pin Plastic LQFP (FPT-100P-M05) 100-pin Plastic QFP (FPT-100P-M06) Package Remarks
59
MB90860A Series
s PACKAGE DIMENSIONS
100-pin Plastic QFP (FPT-100P-M06)
23.900.40(.941.016)
* 20.000.20(.787.008)
80 51
Note 1) * : These dimensions do not include resin protrusion. Note 2) Pins width and pins thickness including plating thickness. Note 3) Pins width do not include tie bar cutting remainder.
81
50
0.10(.004) 17.900.40 (.705.016)
*14.000.20 (.551.008)
INDEX Details of "A" part
100 31
1
30
0.25(.010) +0.35 3.00 -0.20 +.014 .118 -.008 (Mounting height) 0~8 0.170.06 (.007.002) 0.800.20 (.031.008) 0.880.15 (.035.006) 0.250.20 (.010.008) (Stand off)
0.65(.026)
0.320.05 (.013.002)
0.13(.005)
M
"A"
C
2002 FUJITSU LIMITED F100008S-c-5-5
Dimensions in mm (inches) Note : The values in parentheses are reference values.
(Continued)
60
MB90860A Series
(Continued)
100-pin Plastic LQFP (FPT-100P-M05) Note 1) * : These dimensions do not include resin protrusion. Note 2) Pins width and pins thickness include plating thickness. Note 3) Pins width do not include tie bar cutting remainder.
16.000.20(.630.008)SQ
* 14.000.10(.551.004)SQ
75 51
76
50
0.08(.003) Details of "A" part
INDEX
1.50 -0.10 .059 -.004 (Mounting height)
26
+0.20
+.008
100
0.100.10 (.004.004) (Stand off) 0.25(.010)
0~8 "A" 0.500.20 (.020.008) 0.600.15 (.024.006)
1
25
0.50(.020)
0.200.05 (.008.002)
0.08(.003)
M
0.1450.055 (.0057.0022)
C
2003 FUJITSU LIMITED F100007S-c-4-6
Dimensions in mm (inches) Note : The values in parentheses are reference values.
61
MB90860A Series
FUJITSU LIMITED
All Rights Reserved. The contents of this document are subject to change without notice. Customers are advised to consult with FUJITSU sales representatives before ordering. The information, such as descriptions of function and application circuit examples, in this document are presented solely for the purpose of reference to show examples of operations and uses of Fujitsu semiconductor device; Fujitsu does not warrant proper operation of the device with respect to use based on such information. When you develop equipment incorporating the device based on such information, you must assume any responsibility arising out of such use of the information. Fujitsu assumes no liability for any damages whatsoever arising out of the use of the information. Any information in this document, including descriptions of function and schematic diagrams, shall not be construed as license of the use or exercise of any intellectual property right, such as patent right or copyright, or any other right of Fujitsu or any third party or does Fujitsu warrant non-infringement of any third-party's intellectual property right or other right by using such information. Fujitsu assumes no liability for any infringement of the intellectual property rights or other rights of third parties which would result from the use of information contained herein. The products described in this document are designed, developed and manufactured as contemplated for general use, including without limitation, ordinary industrial use, general office use, personal use, and household use, but are not designed, developed and manufactured as contemplated (1) for use accompanying fatal risks or dangers that, unless extremely high safety is secured, could have a serious effect to the public, and could lead directly to death, personal injury, severe physical damage or other loss (i.e., nuclear reaction control in nuclear facility, aircraft flight control, air traffic control, mass transport control, medical life support system, missile launch control in weapon system), or (2) for use requiring extremely high reliability (i.e., submersible repeater and artificial satellite). Please note that Fujitsu will not be liable against you and/or any third party for any claims or damages arising in connection with above-mentioned uses of the products. Any semiconductor devices have an inherent chance of failure. You must protect against injury, damage or loss from such failures by incorporating safety design measures into your facility and equipment such as redundancy, fire protection, and prevention of over-current levels and other abnormal operating conditions. If any products described in this document represent goods or technologies subject to certain restrictions on export under the Foreign Exchange and Foreign Trade Law of Japan, the prior authorization by Japanese government will be required for export of those products from Japan.
F0405 (c) FUJITSU LIMITED Printed in Japan

▲Up To Search▲

Price & Availability of MB90860A

	To Download MB90860A Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .